Phono Transfer System Construction Information

Construction information for DIY projects, including the MS Mid Side Matrix, Elliptic Equalizer, Mastering Console, Phono Transfer System, Insert Switcher and the Dual Class-A Amplifier. You can post your baby pictures here.
billshurv
Posts: 384
Joined: Thu Feb 01, 2018 7:07 am

Re: Phono Transfer System Construction Information

Post by billshurv » Sat Jul 27, 2019 5:48 pm

Exactly. I have some kelvin probes I want to test out anyway :)

billshurv
Posts: 384
Joined: Thu Feb 01, 2018 7:07 am

Re: Phono Transfer System Construction Information

Post by billshurv » Wed Aug 14, 2019 3:32 am

I have actually started soldering. Based on some previous bad experiences I now never solder after midnight so limited time as eldests is in the room i use as a lab so everything has to be packed away each night. I need a bigger house...

User avatar
mediatechnology
Posts: 3956
Joined: Sat Aug 11, 2007 2:34 pm
Location: Oak Cliff, Texas
Contact:

Re: Phono Transfer System Construction Information

Post by mediatechnology » Wed Aug 14, 2019 11:48 am

Which board are you building?
https://ka-electronics.com

"VIDEO: Leaked ABC News Insider Recording EXPOSES #EpsteinCoverup "We had Clinton, We had Everything"" https://www.youtube.com/watch?v=3lfwkTsJGYA

"There's A War On For Your Mind" Banned.Video https://banned.video/

billshurv
Posts: 384
Joined: Thu Feb 01, 2018 7:07 am

Re: Phono Transfer System Construction Information

Post by billshurv » Wed Aug 14, 2019 5:06 pm

I'm starting with the Flat MM boards, then I'll do the RIAA switchers then the two MC boards. Once both sets are tested then I send one set to the low countries for a friend and I can start playing with my MM cartridges.

User avatar
mediatechnology
Posts: 3956
Joined: Sat Aug 11, 2007 2:34 pm
Location: Oak Cliff, Texas
Contact:

Re: Phono Transfer System Construction Information

Post by mediatechnology » Wed Aug 14, 2019 6:29 pm

I owe you some test instructions for the MC preamp board.
I need to get back on that project.
https://ka-electronics.com

"VIDEO: Leaked ABC News Insider Recording EXPOSES #EpsteinCoverup "We had Clinton, We had Everything"" https://www.youtube.com/watch?v=3lfwkTsJGYA

"There's A War On For Your Mind" Banned.Video https://banned.video/

billshurv
Posts: 384
Joined: Thu Feb 01, 2018 7:07 am

Re: Phono Transfer System Construction Information

Post by billshurv » Thu Aug 15, 2019 3:25 am

Sure I can work that out!

billshurv
Posts: 384
Joined: Thu Feb 01, 2018 7:07 am

Re: Phono Transfer System Construction Information

Post by billshurv » Wed Oct 30, 2019 6:06 pm

OK easy bit is all done. Now working on the customisations for one of the sets and trying to guestimate the gains required. The bit I'm having trouble on is relative levels between Flat and RIAA outputs. I want to think they should be same at around -23dBFS for a 0dB reference cut, but keep thinking I'm missing something.

User avatar
mediatechnology
Posts: 3956
Joined: Sat Aug 11, 2007 2:34 pm
Location: Oak Cliff, Texas
Contact:

Re: Phono Transfer System Construction Information

Post by mediatechnology » Wed Oct 30, 2019 7:05 pm

Sounds like progress!

-23 dBFS (flat) is my target for 1 kHz 5 cm/s.

The RIAA filter has a -2.25 dB insertion loss at 1 kHz which is usually made up at VR3/VR4.
If the RIAA is set for unity gain overall the subjective levels between flat and EQ'd are pretty close.

There's 6 dB of gain built in RIAA EQ monitor due to the THAT1646 and 6 dB in the cross-coupled output of the MM and MC preamps.
The INA front-end gain should thus be 12 dB less than the overall required gain.
The INA gain is 1+[(2*Rfb)/Rg] for both the MM and MC preamps.
https://ka-electronics.com

"VIDEO: Leaked ABC News Insider Recording EXPOSES #EpsteinCoverup "We had Clinton, We had Everything"" https://www.youtube.com/watch?v=3lfwkTsJGYA

"There's A War On For Your Mind" Banned.Video https://banned.video/

billshurv
Posts: 384
Joined: Thu Feb 01, 2018 7:07 am

Re: Phono Transfer System Construction Information

Post by billshurv » Thu Oct 31, 2019 4:52 am

Wife is away for half term. But have put down the soldering iron whilst I measure twice and cut once on the build I am doing for a friend. Next step is working out positionng of the 26 relays needed!

Post Reply